BMW INPA K+CAN With FT232RL Chip K DCAN USB Interface
Interface USB OBD2 for BMW – INPA/Ediabas – K+DCAN allows full diagnostic of BMW from 1998 to 2008 (all functions as in OMNITEC interface). Build in 2 lines K and D-Can magisterial
Bmw k1600 grand america download brochure. As a fully-equipped luxury tourer, the BMW K 1600 Grand America offers relaxed driving pleasure, maximum comfort and ample space with unrivaled running culture.
BMW INPA Ediabas 5.0.2 download, inpa 5.06 download, inpa 6.4.7 download here…and install it on Windows XP/ Vista or Windows 7/ 8/ 10 (32bit or 64bit), to get it work with K+DCAN USB cable.
INPA download
Where to download and how to install Here you go. NOTE: I am NOT responsible for any damage YOU do to your car or computer.BMW INPAwill work with few select things for an E38 such as resetting adaptations, diagnostics, code reading, etc. NCS Expert will NOT run on a 64-bit operating syetm.
INPA 5.0.2 download (tested OK)
More: INPA Ediabas download
BMW inpa cable
Basically, there are two methods for users to get the INPA K+DCAN usb cable, to buy a complete one or simply build one yourself. Read the following to get it.
One way is to build a cable yourself. Cost for this would probably range anywhere between 10 to 20 bucks. You will need to solder a bit but it's nothing too serious if you follow the instructions to the letter.
Its actually very simple that any average person can do that has access to a drill and a soldering gun.
Tools needed.
1. Small philip screwdriver to take the D-can cover off
2 Radio Shack micro on/off switch (can be two prongs or three) and some wire 24 guage.
3. Soldering gun
4. Some type of glue gun or glue adhesive
5. Drill bit 5/16 to make hole in the D-can cover
Locate pin 8 which will have a number on the side of the board. One side will have the digit 1 and the other digit 8
Once you locate pin 8, thats the pin we will be using as well as the next one over. Connect each pin 7 and 8 with a separate wire and then use the soldering gun and connect each wire to the micro on/off switch… If you bought a 2 prong on/off switch connect it to each side, but if you bought a switch with three prongs, connect the middle and one of the ends, doesnt matter which one. At the end there will be one prong end not used…Neatly place the wires snug so that the D-can cover can be closed without anything preventing it to make a closed seal and your done. Screw in the 4 philip head screws in their respected holes. Note which postion is on and which is off by some type of label on the outside of the cover…SImple! Note on my first pic, I have a switch with 3 prongs, but I snipped off the 3rd one just to make it easier to solder…
Download For Windows 10 Free
I modified my cable with a switch and have 7 and 8 bridged to work with a 2004 E46. INPA and Dis 44 work perfect but I cant get Progman to work. Progman starts to reads the FA/ZCS after you choose the car model and then after awhile it says it requires an Edic/Icom cable connection. What needs to be done to make connection with Progman SSS V32?? Do I need to change anything in the Ediabas configuration. I know my modified cable works fine now that I modified it because Dis 44 and INPA wasn't communicating before I modified the cable. Thanks for the help. I am stumped as I want to code the car for my brother-in-law. I actually can use Dis 44 as I already went into the CKM coding menu, but Progman is much better to help him choose his features he wants as its pretty much offers a checklist with dots!
Took a pic of my success with my modified D-can cable connected to E46 using Progman. My brother-in-law had no idea he had so many features that were not turn on…He also turn off his daytime running lights which he hated!
(NOTE: this diy guide is from cn555ic at e90post.com, the professionals have not tried, put it here )
But if you are not interested in building one, buy a dedicated BMW cable instead. This is a site that has been confirmed working by some of E-series friends: http://www.autocardiag.com/inpa-kcan-with-ft232rl-chip-for-bmw-obd2-interface-p-468.html . I wouldn't recommend other sites, although they may work, problem is that they have not been confirmed working yet. Functions of k+dcan cable at obdii365 has been tested for years (many discussion in forums).
The version 2016 cable is great, designed with the FT232RQ chip and a switch to turn LEFT is for 7 pin or RIGHT for 8 pin (8 pin for K-LINE communication (old DCAN cables cannot do it) for BMW from 1998 to 2008)
the chips and switch on the cable….
INPA installation guide…Here you go…
Here, inpa installation guides for Windows XP, Windows Vista 32bit, Windows 7 32, Windwos 7 64bit, Windows 8, Windows 10 users. (click on the Operation System to get the how-to guide directly).
Note: INPA 5.0.2 is verified to work XP systems without any issues. For others, you need luck!
24hour Online Customer Service:
E-mail:autocardiag@gmail.com
Skype:Marshall.obd2
Whatsapp:86-13476108995
http://www.autocardiag.com
Save
Save
where to download and how to install… Here you go.
NOTE: I am NOT responsible for any damage YOU do to your car or computer.BMW INPAwill work with few select things for an E38 such as resetting adaptations, diagnostics, code reading, etc. NCS Expert will NOT run on a 64-bit operating syetm. If you have a 32-bit version of Windows 10, please feel free to try ECS Expert and let me know if it works!
I have NOT tried INPA with any other bmw models. Please feel free to comment your success on other models!!
BMW INPA Windows 10 download links:
Bmw Dis V57 Software Download For Windows 10
K+DCAN usb cable:
Switch mode K+DCAN cable:
http://www.cardiagtool.co.uk/bmw-inpa-k-can-with-ft232rq-chip.html
INPA software 5.0.2:
https://www.dropbox.com/s/wvgykv0zg2scju9/INPA.rar?dl=0
Free real-time updates! Your manual is updated with revised information as soon as it is released. Access on your terms. Unlimited access to your 1991 Toyota Corolla manual on a yearly basis. 100% No Risk Guarantee. We'll get you the repair information you need, every time, or we'll refund your purchase in full. 1991 Toyota Corolla repair. Toyota Corolla. If you want an affordable, practical and economical car, chances are you'll probably end up with a Toyota Corolla. It's one of the best-selling cars of all time, a car which shaped the very automotive world we live in today. Very few cars have influenced the automotive industry as much as the Toyota Corolla has. Dec 28, 2017 Toyota Corolla repair manual, fault codes, wiring diagrams PDF free download See also: Toyota Chaser repair manual Toyota Camry repair manual Toyota Service Manuals These repair manuals covers the operation and repair of the Toyota Corolla. The book describes the repair of cars with gasoline and diesel engines 4ZZ-FE / 3ZZ-FE / 2ZZ-GE / 1CD-FTV in volume 1.4, 1.6, 1.8 and 2.0D liters with a. Free pdf for 1991 toyota corolla shop manual.
INPA cable software:
Ford 3600 service manual download. Schematics 4 FreeService manuals, schematics, documentation, programs, electronics, hobby.Login:Pass:Search service manuals databaseMfg:Type:Show FilesOrder byType:SizethanClass:Please, enter search term!Search results for: (found: )FileDateDescrClassSizePopularMfgModelOriginalAdded byNo Results Found!
Please allow time for these downloads. They are fairly good sized.
How to setupINPA 5.0.2 on Windows 10 64bit:
Should you get ANY errors or pop-ups during any phase of the installation, ignore them. INPA will still install.
Pre-Installation
1.Download all required files and programs,as listed below. Also you should have the K+DCAN cable in your posession(link provided below).
2.Extract the INPA.rar to your desktop. You will be left with INPA folder.
3.Extract INPAcable.rar to your desktop. You will be left with INPA cable folder.
Installation – Phase 1
1.Open INPA cable folder and move the top four folders (step1, step2, step3 and driver) to Windows(Cfolder of your PC.
2.Whilst in Windows(C, open 01_Step1 folder and copy EC-APPS over to your Windows(Cdrive.
3.Go back to 01_Step1 folder and open the NFS folder. Open Entpackt folder. Open disk 1, find SETUP.exe and right-click it. Goto Properties/Compatibility and set it to run in compatibilty mode for Windows XP (Service Pack 3). Also, check the box for Run as Administrator. Hit Apply then Ok.
4.Double-click SETUP.exe to launch.
5. Once window pops up, select Windows XP. Click Weiter (it means Next).
6.Click Weiter 3 more times. Make sure User Mode is selected. Click weiter.
7.Make sure top choice is selected (1 Parametri……). Click Weiter.
8.Ensure OBD is selected. Press weiter. Ensure Kein API-TRACE. Click weiter. Ensure Kein IFH-TRACE is selected. Click weiter.Ensure Komfort(.IPO) is selected. Press weiter.
9.Press OK. Let install. Press ok, and again. Press any key to continue.
10.Select Ja,Computer jetzt neu starten. Click Breeden. This will restart your PC as needed.
Phase 2
1.Goto Windows(C/02_Step_2/INSTALL and right click on Instprog. Set it up to run in compatibility mode as mentioned in Phase1, step 3. Then double-click to launch.
2.Press OK if prompted. Select Enlgish then press weiter.
3.Press continue and continue again. Ensure destination is under C:
4. Press continue. Select BMW Group Rectification programs UK. (NOT USA) Press continue.
5.Check off all white boxs. There will be 2 update and 1 complete that needs to be checked. Press continue, and again. You may get error. ignore it. Otherwise, press End.
6.Restart your PC once more manually.
Phase 3
1.Goto Windows(C/03_Step_3/INSTALL and right click on Instprog. Set it up to run in compatibility mode as mentioned in Phase1, step 3. Then double-click to launch.
2.Press OK if prompted. Select Enlgish then press weiter.
3.Press continue and continue again. Ensure destination is under C:
4. Press continue. Select BMW Group Rectification programs UK. (NOT USA) Press continue.
5.Under INPA 5.0.1, check off Update. Under NCS Expert 3.0.8, check off Complete. Press continue.
6.Click on Rename. In the box, type the number 1 and press continue, and again. You might gett error. Ignore it. IF prompted, press End.
Phase 4
1.Plug in your K+DCAN cable. You will from now on use ONLY that port.
**Windows 10 will autoatically update the driver IF needed. Windows 10 also already has a serial function. This is all we need to modify.**
2.In your search box (lower left of screen next to Windows button), type 'Device Manager'. Click on the top option.
3.Once in Device Manager, locate Ports(COM & LPT) and click on the little plus sign next to it. It should now show USB Serial Port (COMx) under Ports(COM & LPT). **The little ‘x' is in place of whatever number you have the cable plugged into).
4.Right-click on USB Serial Port (COMx) and click Properties.
5.Goto Port Settings tab. Click Advanced. Change the COM Port Number to COM1.
6.Change Latency Timer from 16 to 1. Press ok. Press ok again. Close Device Manager.
7.Goto Windows(C/Driver_D_CAN_USB and double-click OBDSetup.exe. Press Enter.
Phase 5
1.Go into Control Panel/System/Advanced System Settings/Environment Variables.
2.Ensure that System Variables TMP and TEMP both contain the path C:EDIABASBin.
3.If not, manually add it in. Example: C:WindowsTemp;C:EDIABASBin
4.the ‘;' is important to seperate paths. Please ensure you put that in there then add in the rest.
Phase 6
1.From Desktop, open INPA folder then open the second INPA folder. Right click on Step_1_Install_BMW_Tools and click Poperties. Goto Compatibilty and run the program in compatibility mode for Windows 7. Also, run as administrator. Click Apply then ok. Doulbe-click to launch.
2.Enusre destination path is C:BMW Tools , if it is not change it to that.
3.Press Install. You will get an error. Press ok.
4.Goto Windows(C/BMW Tools/Programminstallation and right-click on setup.exe. Set it up for compatibility mode as stated in Phase 1, step 3.
5.double-click to launch. Select English, press ok. Press Next. Accept and press next. Press next again and again.Ensure the installation destination is C:EDIABAS, click next.Ensure installation destination is C:EC-APPSNFS,click next.Ensure installation destination is C:EC-APPSINPA, click next.Ensure installation destination is C:NCSEXPER, click next.Ensure start menu folder is BMW Standard Tools. click next.
6.You do NOT have to perform the data backup if not desired. I didn't. Uncheck box if not wanting data backup and click next.Ensure hardware-interface setting is STD:OBD and click next.Ensure COM port for serial OBD is Com1. Check the box for USB to serial adapter. click next. Click Install. If any errors, ignore them.
Phase 7
1.Goto Desktop/INPA/INPA and right-click the file ‘Step 2_ Install INPA.exe'.Set up for compatibility as mentioned in Phase 6,step 1.
2.The Destination Path should be ‘C:temp', leave as it is and click ‘Next'.
3.Choose ‘English' and select ‘Continue' and ‘Continue'.
4.Select ‘C:' and then ‘Continue'.
5.Select ‘BMW Group Rectification Programs UK' and click ‘Continue'.
6.Tick ‘Update' for all options where not grayed out, then ‘Continue'.
7.Select ‘OBD', then ‘Continue' and ‘Continue'.
8.The installation will begin and complete.
Phase 8
1.Goto Desktop/INPA/INPA and right-click the file ‘Step 3_ Final Update.exe'.Set up for compatibility as mentioned in Phase 6,step 1.
2.The Destination Path should be left as it is, then select ‘Install'.
3.Select ‘Yes to all'.
4.Once completed, the window will close itself.
Phase 9
1.Goto Desktop/INPA/INPA and double-click the file ‘serial port.reg'.
2.When prompted, select ‘Yes' and ‘Yes'. You will receive confirmation that your registry has been updated.
3.Locate the file ‘C:EDIABASBinobd.ini' and copy this file into your Windows folder.
4.Edit the file ‘C:EC-APPSINPACFGDATINPA.INI' in Notepad, locate the section that starts with ‘//F3', remove the slashes at the beginning of the three lines of text, and amend any instance of ‘F10' to ‘E46'.
**Step 4 is only needed if you are working on an E46. Otherwise, ignore this step!
In theory, you will not have INPA on your desktop. Right-click it and set up compatibility mode as mentioned in Phase 1, step 3. Double click to launch.
Credits:
http://www.bimmerforums.co.uk/forum/…64bit-t103023/
https://www.bimmerforums.com/forum/…INPA-Windows-10-64-bit-Installation-Guide
I utilized these couple of great tutorials, gathered all files needed, made my own .rar files and layed out the instructions as required to getINPA softwareworking on Windows 10 64-bit.
Bmw Dis Download For Windows 10 2016
The final tip:
Bmw Dis Download For Windows 10 32 Bit
ICOM A2can be used with diagnosis and also programming. While DCAN cable can do all of those it is not safe to program modules because there have been a lot of cases where modules were bricked.You can only get your 1B file using FSC generator with ICOM on an E series car but cannot generate 1B file using a DCAN cable since it will give you an error. There is another way though of getting your 1B file without using an ICOM on an E series through the USB port inside your glovebox accessing the hard drive directly. Rather than going through all those stuff, it is more convenient to just buy the lifetime FSC code and be done with it.
To see if I understood:
Programming= Flashing a module, which means changing the actual software. Best done with an ICOM.
Coding= Reading and writing the memory which contains the configuration. Can be done with a K&DCAN cable.
Bmw Dis Download For Windows 10 Chrome
ICOM: fast protocol, allows to secure flash software and read/write access the entire memory. Similar to JTAG programming.
K&DCAN Cable: slow serial protocol, flashing would take ages and errors could occur. Also, not possible to access the entire memory. Similar to RS232 bootloader access.
You program a module if you want to update the software to a newer one or if you a retrofitting a new module and want to flash it. ICOM is a lot more stable than dcan cable when it comes to programming. And you are right there are modules that takes hours to finish and any interruption in the process will surely brick that module. You can get a cheap china clone ICOM but finding a refutable vendor selling a good working ICOM is not easy. I've been using China ICOM from http://www.cardiagtool.co.uk/bmw-inpa-k-can-with-ft232rq-chip.html it's a good helper in my garage repair work. You can also getrecommendations from others who bought a working clone ICOM.